全文获取类型
收费全文 | 8913篇 |
免费 | 1008篇 |
国内免费 | 763篇 |
专业分类
化学 | 3285篇 |
晶体学 | 117篇 |
力学 | 2877篇 |
综合类 | 71篇 |
数学 | 1495篇 |
物理学 | 2839篇 |
出版年
2023年 | 98篇 |
2022年 | 160篇 |
2021年 | 226篇 |
2020年 | 270篇 |
2019年 | 229篇 |
2018年 | 229篇 |
2017年 | 285篇 |
2016年 | 346篇 |
2015年 | 290篇 |
2014年 | 431篇 |
2013年 | 732篇 |
2012年 | 451篇 |
2011年 | 557篇 |
2010年 | 434篇 |
2009年 | 550篇 |
2008年 | 518篇 |
2007年 | 575篇 |
2006年 | 492篇 |
2005年 | 419篇 |
2004年 | 422篇 |
2003年 | 331篇 |
2002年 | 269篇 |
2001年 | 258篇 |
2000年 | 225篇 |
1999年 | 191篇 |
1998年 | 200篇 |
1997年 | 185篇 |
1996年 | 191篇 |
1995年 | 130篇 |
1994年 | 127篇 |
1993年 | 140篇 |
1992年 | 114篇 |
1991年 | 96篇 |
1990年 | 75篇 |
1989年 | 65篇 |
1988年 | 44篇 |
1987年 | 55篇 |
1986年 | 49篇 |
1985年 | 33篇 |
1984年 | 33篇 |
1983年 | 22篇 |
1982年 | 40篇 |
1981年 | 24篇 |
1980年 | 20篇 |
1979年 | 15篇 |
1978年 | 8篇 |
1976年 | 3篇 |
1973年 | 5篇 |
1970年 | 5篇 |
1957年 | 4篇 |
排序方式: 共有10000条查询结果,搜索用时 15 毫秒
1.
2.
3.
针对机油滤清器工作工况下进出口压差、机油滤层强度及导流桩高度等问题, 通过试验测试与仿真相结合, 对滤清器初步设计进行了评估及优化, 以确保滤清器在工作工况下进出口压降及滤层强度能满足要求. 首先进行滤层性能试验, 得到滤层的惯性阻力系数和黏性阻力系数; 再通过滤层多孔介质CFD分析, 对滤清器进出口压降进行分析计算. 结果表明: 在-18℃、25℃和70℃的工况下, 进出口压降都小于10kPa, 满足相关要求. 针对滤层的最大主应力超过其抗拉强度的问题, 通过CAE仿真分析, 优化滤层与导流桩间隙, 将滤层最大主应力由110.1MPa降至36.99MPa, 小于其抗拉强度42.8MPa. 相似文献
4.
移动加热器法(THM)生长碲锌镉晶体时,界面稳定性对晶体生长的质量有很大影响。本文基于多物理场有限元仿真软件Comsol建立了THM生长碲锌镉晶体的数值模拟模型,讨论了Te边界层与组分过冷区之间的关系,对不同生长阶段的物理场、Te边界层与组分过冷区进行仿真研究,最后讨论了微重力对物理场分布的影响,并对比了微重力与正常重力下的生长界面形貌。模拟结果表明,Te边界层与组分过冷区的分布趋势是一致的,在不同生长阶段,流场中次生涡旋的位置会发生移动,从而导致生长界面的形貌随着生长的进行发生变化,同时微重力条件下形成的生长界面形貌最有利于单晶生长。因此,在晶体生长的中前期,对次生涡旋位置的控制和对组分过冷的削弱,是THM生长高质量晶体的有效方案。 相似文献
5.
This study compares the physicochemical properties of six electrolytes comprising of three salts: LiFTFSI, NaFTFSI and KFTFSI in two solvent mixtures, the binary (3EC/7EMC) and the ternary (EC/PC/3DMC). The transport properties (conductivity, viscosity) as a function of temperature and concentration were modeled using the extended Jones-Dole-Kaminsky equation, the Arrhenius model, and the Eyring theory of transition state for activated complexes. Results are discussed in terms of ionicity, solvation shell, and cross-interactions between electrolyte components. The application of the six formulated electrolytes in symmetrical activated carbon (AC)//AC supercapacitors (SCs) was characterized by cyclic voltammetry (CV), galvanostatic cycling with potential limitation (GCPL), electrochemical impedance spectroscopy (EIS) and accelerated aging. Results revealed that the geometrical flexibility of the FTFSI anion allows it to access and diffuse easily in AC whereas its counter ions (Li+, Na+ or K+) can remain trapped in porosity. However, this drawback was partially resolved by mixing LiFTFSI and KFTFSI salts in the electrolyte. 相似文献
6.
S.V. Ivanov M.Yu. Chernov V.A. Solovev P.N. Brunkov D.D. Firsov O.S. Komkov 《Progress in Crystal Growth and Characterization of Materials》2019,65(1):20-35
High-efficiency semiconductor lasers and light-emitting diodes operating in the 3–5?μm mid-infrared (mid-IR) spectral range are currently of great demand for a wide variety of applications, in particular, gas sensing, noninvasive medical tests, IR spectroscopy etc. III-V compounds with a lattice constant of about 6.1?Å are traditionally used for this spectral range. The attractive idea to fabricate such emitters on GaAs substrates by using In(Ga,Al)As compounds is restricted by either the minimum operating wavelength of ~8?μm in case of pseudomorphic AlGaAs-based quantum cascade lasers or requires utilization of thick metamorphic InxAl1-xAs buffer layers (MBLs) playing a key role in reducing the density of threading dislocations (TDs) in an active region, which otherwise result in a strong decay of the quantum efficiency of such mid-IR emitters. In this review we present the results of careful investigations of employing the convex-graded InxAl1-xAs MBLs for fabrication by molecular beam epitaxy on GaAs (001) substrates of In(Ga,Al)As heterostructures with a combined type-II/type-I InSb/InAs/InGaAs quantum well (QW) for efficient mid-IR emitters (3–3.6?μm). The issues of strain relaxation, elastic stress balance, efficiency of radiative and non-radiative recombination at T?=?10–300?K are discussed in relation to molecular beam epitaxy (MBE) growth conditions and designs of the structures. A wide complex of techniques including in-situ reflection high-energy electron diffraction, atomic force microscopy (AFM), scanning and transmission electron microscopies, X-ray diffractometry, reciprocal space mapping, selective area electron diffraction, as well as photoluminescence (PL) and Fourier-transformed infrared spectroscopy was used to study in detail structural and optical properties of the metamorphic QW structures. Optimization of the growth conditions (the substrate temperature, the As4/III ratio) and elastic strain profiles governed by variation of an inverse step in the In content profile between the MBL and the InAlAs virtual substrate results in decrease in the TD density (down to 3?×?107 cm?2), increase of the thickness of the low-TD-density near-surface MBL region to 250–300?nm, the extremely low surface roughness with the RMS value of 1.6–2.4?nm, measured by AFM, as well as rather high 3.5?μm-PL intensity at temperatures up to 300?K in such structures. The obtained results indicate that the metamorphic InSb/In(Ga,Al)As QW heterostructures of proper design, grown under the optimum MBE conditions, are very promising for fabricating the efficient mid-IR emitters on a GaAs platform. 相似文献
7.
Four kinds of red phosphorescent organic light-emitting devices were fabricated and compared to investigate the effect of interfacial layers for hole transport and electron injection. 1 nm-thick LiF in the device A and C and 1 nm-thick Cs2CO3 in the device B and D were deposited as an electron injection layer between the anode and the electron transport layer, and 5 nm-thick layer of dipyrazion[2,3-f:2′,2′-h]quinoxaline-2,3,6,7,10,11-hexacarbonitrile[HATCN] was inserted as a hole transport interfacial layer between the hole injection layer and the hole transport layer only in the device C and D. Under a luminance of 1000 cd/m2, the power efficiencies were 7.6 lm/W and 8.5 lm/W in the device A and B, and 8.6 lm/W and 13.4 lm/W in the device C and D. The quantum efficiency of the device D was 15.8% under 1000 cd/m2 which was somewhat lower than those of the device A and C, but a little higher than that of the device B. The luminance of the device D was much higher than those of the other devices at a given votage. The luminance of the device D at 7 V was 23,710 cd/m2, which was 13.0, 3.4, and 4.0 times higher than those of the device A, B, and C at the same voltage, respectively. 相似文献
8.
Kai Xu Zhenchang Tang Yan Zhang Wanshu Li Haiou Li Lihui Wang Liming Liu Honghang Wang Feng Chi Xiaowen Zhang 《Current Applied Physics》2019,19(10):1076-1081
Germanium dioxide (GeO2) aqueous solutions are facilely prepared and the corresponding anode buffer layers (ABLs) with solution process are demonstrated. Atomic force microscopy, X-ray photoelectron spectroscopy and ultraviolet photoelectron spectroscopy measurements show that solution-processed GeO2 behaves superior film morphology and enhanced work function. Using GeO2 as ABL of organic light-emitting diodes (OLEDs), the visible device with tris(8-hydroxy-quinolinato)aluminium as emitter gives maximum luminous efficiency of 6.5 cd/A and power efficiency of 3.5 lm/W, the ultraviolet device with 3-(4-biphenyl)-4-phenyl-5-tert-butylphenyl-1,2,4-triazole as emitter exhibits short-wavelength emission with peak of 376 nm, full-width at half-maximum of 42 nm, maximum radiance of 3.36 mW/cm2 and external quantum efficiency of 1.5%. The performances are almost comparable to the counterparts with poly (3,4-ethylenedioxythiophene):poly (styrenesulfonate) as ABL. The current, impedance, phase and capacitance as a function of voltage characteristics elucidate that the GeO2 ABL formed from appropriate concentration of GeO2 aqueous solution favors hole injection enhancement and accordingly promoting device performance. 相似文献
9.
Facile non‐lithographic route to highly aligned silica nanopatterns using unidirectionally aligned polystyrene‐block‐polydimethylsiloxane films 下载免费PDF全文
Zhe Qiang Maurice L. Wadley Bryan D. Vogt Kevin A. Cavicchi 《Journal of Polymer Science.Polymer Physics》2015,53(15):1058-1064
Thin films (monolayer and bilayer) of cylinder forming polystyrene‐block‐polydimethylsiloxane (PS‐b‐PDMS) were shear aligned by the swelling and deswelling of a crosslinked PDMS pad that was physically adhered to the film during solvent vapor annealing. The nanostructures formed by self‐assembly were exposed to ultraviolet‐ozone to partially oxidize the PDMS, followed by calcination in air at 500 °C. In this process, the PS segments were fully decomposed, while the PDMS yielded silica nanostructures. The highly aligned PDMS cylinders were thus deposited as silica nanolines on the silicon substrate. Using a bilayer film, the center‐to‐center distance of these features were effectively halved from 38 to 19 nm. Similarly, by sequential shear‐alignment of two distinct layers, a rhombic array of silica nanolines was fabricated. This methodology provides a facile route to fabricating complex topographically patterned nanostructures. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1058–1064 相似文献
10.
以焦炉上升管内壁结焦炭层块为研究对象,采用X射线荧光光谱仪(XRF)、X射线衍射仪(XRD)、傅里叶红外光谱仪(FTIR)和激光共聚焦拉曼光谱仪(Raman)对结焦炭层的元素组成,以及各结焦炭层的矿物组成、组成结构和分子结构进行测试。分析从结焦炭层块外表面向内表面过渡的各结焦炭层的差异性,揭示焦炉上升管内壁结焦机理。结果表明焦炉上升管内粉尘中Fe,S和Cr极易催化荒煤气中蒽、萘等稠环芳烃化合物成炭,在焦炉上升管内壁形成炭颗粒沉积,为焦油凝结挂壁提供载体,在荒煤气温度降至结焦温度时易结焦积碳。结焦炭层均含有芳香层结构,随着结焦炭层从外表面向内表面过渡,各结焦炭层的面层间距(d002)逐渐降低、层片直径(La)先降低后增加、层片堆砌高度(Lc)和芳香层数(N)先稳定后增加。结焦炭层石墨化过程是由结焦炭层内表面向外表面进行,主要包括其片层外缘的羧基和部分C-O结构的降解剥离,从而形成高度规整的共轭结构。结焦炭层块中C元素是以结晶碳与无定型碳的混合物形式存在。以上研究为解决焦炉上升管内壁结焦及腐蚀问题,提高换热器换热效率,有效回收焦炉荒煤气显热,降低焦化企业能耗提供实验基础和理论依据。 相似文献